from USA
to UAE
in 5-8 days
At your doorstep by May 23  to May 26 with standard delivery


  • Digital clamp meter measures alternating current (AC) and direct current (DC), AC and DC voltage, resistance, and frequency Average-sensing meter provides accurate readings when measuring linear loads where the current or voltage has a sinusoidal waveform Clamp with 1.3" (35 mm) jaw opening measures current without touching or interrupting the circuit Peak + or - function records instantaneous peak values for current and voltage Meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V.
  • Imported from USA.
Style:Megger DCM340-EN The Megger DCM340-EN digital clamp meter is an average-sensing multimeter for measuring current, voltage, resistance, and frequency in electrical testing applications. It has a clamp with two jaws that can close around an electrical conductor up to 1.3" (35 mm) in diameter to measure current without touching or interrupting the circuit. The meter comes with detachable test leads that measure voltage, resistance, and frequency. The peak + or - function records instantaneous peak positive or negative values for current and voltage. The maximum or minimum reading mode displays the highest or lowest reading in a session to track a sudden increase or decrease in readings. The relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing quick comparison of multiple readings. An audible continuity sensor confirms that the circuit conducts electricity. The hold function keeps a reading on the display, even after the meter is disconnected. The meter's liquid crystal display (LCD) shows readings in digits and on a bar graph and is backlit to provide readability in low light. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock. The meter can survive falls of up to 1.2 meters to a hardwood or concrete floor. This average-sensing, or average-responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. It has a 4,000-count resolution, meaning that it can display up to 3,999 units (3-3/4 digits) before the operating range needs to be changed. The meter meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V, which covers items used with enclosed building circuit installations (such as service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply). The unit comes with a pouch for transporting and storing the meter. Specifications -------------- Maximum alternating current (AC) input600 ampMaximum direct current (DC) input600 ampMaximum AC voltage input600 volts (V)Maximum DC voltage input600VMaximum resistance detected400 ohmsMaximum frequency detected400 hertz (Hz)Power supply9V PP3 or 6LR61 battery (one, installed)Standards met and certificationsInternational Electrotechnical Commission (IEC) safety standard 61010-1; European Conformity (CE)Weight7.94 oz./225 gMeter dimensions9.33 x 2.68 x 1.65 inches/237 x 68 x 42 mm (H x W x D) H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) standard 9001:2008. What’s in the Box? * Megger DCM340-EN average-sensing digital clamp multimeter * (1) Set test leads * (1) 9V battery (installed) * Carrying pouch * Instructions

Megger DCM340-EN AC/DC Clamp Meter, 400 Ohms Resistance, 600V AC/DC Voltage, 600A AC/DC Current, 400Hz Frequency


Related Pages

Disclaimer: The price shown above includes all applicable taxes and fees. The information provided above is for reference purposes only. Products may go out of stock and delivery estimates may change at any time. desertcart does not validate any claims made in the product descriptions above. For additional information, please contact the manufacturer or desertcart customer service. While desertcart makes reasonable efforts to only show products available in your country, some items may be cancelled if they are prohibited for import in United Arab Emirates. For more details, please visit our Support Page.