onlyfire Universal Spark Generator Replacement for Gas Grill Model

Needed a replacement ignitor for a ProComm / Feature Comforts propane ventless heater model MD300TBE (in owners manual also listed for MD100TBE and MD200TBE). Original ignitor part model number is DHLG-12 dated 2010, 1.5V DC. Yes, got money's worth out of this original part, over twelve years strong. Clicker stopped clicking from previous attempts to clean battery corrosion off. Looked up part at ProComm heater site and the current ignitor part number is PIMSC1-01 but out of stock. Took a chance on this one and it fits. Important to know is the hole to accept the ignitor on the heater has to be approximately 3/4 of an inch across to fit ignitor into hole. If hole is smaller, then may need to file down edge on heater a little to fit. This fit our propane heater fine with no adjustment. If you open the heater and the ignitor looks similar this should work. We bought the one plug model. The ignitor block has a flat square plug end embedded in the bottom corner. The thin wire on the heater is round looking, but it still fits on a blade end. The ignitor plug blade must be aligned with the seam in the wire plug. The existing wire on the unit looks like a round end but fits on a flat square blade. Did not think it would fit, but looked at original part blade and it is the same as new part, flat blade. Blade aligns with seam then slips on. Round wire end to square, works. For heater install. Took the screws off face of heater, unscrewed the old ignitor part, pulled off wire, positioned the new ignitor in heater hole, spun on the included plastic nut, dropped in a AAA battery, put the rubber cap on it and now clicks away like normal. This was a good price and with prime was delivered next day. Now if it lasts as long as the original then great. Just remember to take out the batteries when not in use for the season or occasionally check for leaky batteries. Hope those with a propane heater find this helpful since this is advertised mostly for bbq grills. It just basically clicks to make a spark to ignite the pilot light.

This thing works great. Installed and had my grill working in under ten minutes. A good product

I ordered this to replace the faulty igniter on my Phoenix grill because the Phoenix igniter is $50! I had to wallow the hole out just a tiny bit, I expected that, and it works perfectly. The question now is how long will it last?

The unit works great. I can't give it 5 stars because though because it's a little too big to fit through the hole of my Broil Mate grill. Luckily I have the tools and know-how to drill out the hole and make it a little bigger so it would fit through. Once that was accomplished, installation was a breeze and the unit performs flawlessly.

Worked great on our kenmore grill.

Excellent replacement to CharBroil broken ignitor. Just ensure you order the right one (check BBQ ignitor wire numbers on your BBQ before ordering). Easy to install. If BBQ frame ignitor holding "hole" is smaller, you could drill it bigger of just hold it with zip ties. Very fast ignition vs old one. Important: make sure it doesnt get wet! (use a BBQ cover).

Works good but had to enlarge mounting hole

I got this to replace an ignitor on my ProComm propane/natural gas heater. I read a review that it fit another ProComm so gave this a try. It arrived and was slightly bigger than the one that failed. I think the secret on sizing is the battery. If you have a "AA" this is your pick, if you have a "AAA" this will be too big (I had a "AAA"). Rather than send back due to my miss estimation, I used a file to increase the mounting hole by about 1/16" all around. It fit fine after that and the 2 ignitor wires fit perfect. Once that battery was installed, it worked perfect.

Este producto no lo encontré en ninguna de las tiendas especializadas de boilers y aparatos similares en monterrey, en Amazon lo encontré y llego muy rápido. Funciona ala perfeccion

Perfect fit. Works grear

Works as intended, price is bang on.

Works in my Napoleon grill

Works well.