3M Marine Adhesive Sealant 5200 - Permanent Bonding and Sealing for Boats and Marine Applications - Black - 3 Ounces

This 5200 is the best. I had issues with my 3 seasons room leaking at the outside sill areas. I tried many other silicone sealants. This 5200 did the job. Excellent product. Will buy again. Messy but worth every penny!!!

Best product has a sealant on the market. Highly recommend will hold anything tight and waterproof.

Purchased this product to attempt to seal a challenging flashing issue which has three different material in an awkward transition. I removed all the material from the previous two attempts to waterproof the area, leaving a larger than previous opening to work this material into. After cleaning and prepping the surfaces, I began to applying this 3M product. It is thick, but not problematic to dispense - possibly other reviewers were dispensing through a smaller orifice than me - I used the full tube opening without a tip. The product is exceptionally easy to manipulate and smooth out - almost putty like. Unlike other products like silicone and polyurethane, it didn't stick much to my applicator and thus stayed were I wanted it (without sag) and also smoothed out easily. Bottom line is it adhered to all three materials, filled the voids perfectly, looks great, and the leak is no more! I highly, highly recommend this product - it's amazing!

This is always the best choice

i worked in the boating industry for 35 yrs. doing everything bow to stern top to bottom inside and out. the black is ok but takes quite a while to cure. if you really want an fast indestructable adhesive sealant use the 3m white fast cure. this stuff actually cures faster when exposed to moisture just as it says on the package. many many times i have used this on thru hull fittings, bonding wood, fiberglas, steel, stainless, aluminum and many other materials and it even cures underwater. it will cure in about 12 hrs. once cured it bonds to practically anything. i even use it to repair soles on my shoes if they come apart. then they are better than new. i have used this stuff wherever you need a serious rubber seal, bonding materia, even seals water pipes,fittings etc. i wish they had made it in black fast cure. not sure why unless there is a difference in the chemical makeup. it can be painted using enamel, polyurethane, laquer. not sure about latex, maybe acrylic. one thing is its almost impossible to cut or remove it.

great wouldn't use anything else

Works good and very strong holding up the plastic bond for tight waterproofing seal. It’s a bit sticky at first but once it cures up in 24 hours it’s rock solid with no water leaks.

Unfortunately, I had to rate this with something.. and there are no negative numbers. I was dumfounded that this product demonstrated 100% failure to do anything it is advertised to do..even for the simplest of use. It failed as an adhesive... and where it would NOT bond it failed to seal. I swim 2.5 - 3 miles everyday and am in the water for anywhere from 80 to 110 minutes non-stop. I customize the swimming goggles I use because I can't find goggles that won't put ring marks on my boney eye sockets and over that kind of time they begin to really hurt. I glue custom cut pieces of an old wet suit to the soft material around the goggle lenses. I read many reviews of this product and bought it because I thought I had found a winner and I'd finally found something that would last... but that was not the case. Within one week the bond failed completely. Now maybe the glue isn't made to withstand chlorine, I don't know.. it wasn't indicated and if it is a marine sealant who's to say someone wouldn't be using it around a pool? It only makes sense it could be. And I might be wrong but it seems the silicone pads on the goggles and rubber wetsuit material would bond (that is to say "melt" together) but what I got was a nice clean surface on both the pieces when they came apart. I put the glue on both surfaces and waited over an hour for it to get sticky (otherwise it was like water), so maybe it doesn't bond to itself. Seems every glue I've ever used recommends doing this. I weighted the bond down overnight and because of the "dry" time, did not get them wet for over a week. I can't imagine using this useless stuff on a boat, or any type of motor, or condition where vibration would be constant. And the kind of set up time required the boat would likely sink if I'm trying to seal water out. I'm glad other people got some satisfaction from it, I sure didn't for that piddly little use...and I'd be willing to bet down the road they will all be doing it again. It took well over a week for the glue to become non-sticky. All in all.. I would not recommend anyone buying this stuff for anything unless you just like the smell of it. Sorry 3m but... best go back to the drawing board.. or put some information together about how, where, what.. maybe "your" definition of marine...directions for application and something on the literature other than the fear based stuff about getting it in the eyes or swallowing it. I normally would not say anything and just throw the stuff away but it was such utter failure...maybe I can save someone the trouble and time I went through.

The 3M White Marine 5200 sealant is great as it solves the issue of mine. Zedi Online was excellent in customer service response, as Mr. Aman is so responsive to my emails and messages as he was so great to help me with the fast delivery. He really puts 100% effort into resolving the issue and helping customers like me. From delivering on time, to giving great communication. A big Thanks to Aman as well as Zedi Online😊

Incredible product for boats or anything that requires permanent repair or attachment. have used it on my boat and exposed to sun and weather for years, no deterioration.

Used to install awning rail on my tent trailer. I was somewhat apprehensive about whether this would hold or not but after driving 4 hours, and on dirt bumpy roads, it has held up amazingly.

Great product. |Awesome adhesion and sealing qualities.

I actually use this to seal up busted drysuit seams. It's thick, but pliable, and takes forever to set, but in that time it seeps into the neoprene pores and fills anything from problematic pinholes to blowouts. stuffs tough and flexible, just a pain to use because of the cure time. worth it though