Black Ultra LED Halos

For the main lights to work it is plug and play. You will have to wire in the halos/LEDs. Be sure to set up your vehicle to adjust the headlights to ensure they are not too low or high. That part was pretty easy and all you need is a Phillips screwdriver to do so. In order to wire your halos/leds, I used the Wirefy T-tap connectors (blue for 18 awg-14awg). All you will need are some wire strippers/crimp tool and maybe so mini diagonal cutters to remove the split lume or wire wrapping. For halos/LEDs to hook up to running lights, connect your red wire to the middle wire(purple/white) on the lower light(brown 3 conductor connector). Your black wire will connect to the wire closest to the connector locking tab. Remember that LEDs only operate on correct polarity. Overall it's fairly easy and they look sharp. I have no issues with the lo beam brightness.

Love them. Make the car look good to

Great upgrade over OEM lights. Easy install. Good value for the money

The quality on these are just what I was wanting, the brightness eh they are nice but I swapped the bulbs out for LEDs and definitely made it where I wanted them to be, and I love the driving lights with the Halos on these! Haven’t noticed and fogging or and water issue on the inside so would recommend these to anyone whose looking. Only thing I’ll say is when I was looking I didn’t notice maybe I missed it but for the driving lights and the Halo lights you have to run special wires to have them to work which you could just tap into you headlight wires but I wanted by halos on 24/7 so I ran my a little differently.

They look great and are much better than another set I bought w/single projector. this low beam is brighter, more even horizontally and more pleasing color light. high beams are not as good as OEM, but still doable, compared to the single projector which was not doable. overall I like these and are keeping them.

Terrible headlights. I was sent very defective headlights and one of them had already scratches on it as it was us3d but someone else and got returned to the seller. It was too late for me to return it as I did not get the chance to install till very late b4cause I was super busy. The seller did not provide any resolution to this issue and so it was a waste 5o my money. I would advise to buy from other sellers than this seller. Very poor customer service. Not worth your dime.

These vibrant lights made my 2013 ford look so much newer and cooler. I get asked about my halo lights frequently. It took a minute to figure out how to get them installed and the halos to work without killing my battery. But once figured out, Ive never had another problem.

I do lots of tinkering, but this is my first attempt at wiring. Here are some notes from my install on a 2009 Ford Expedition XLT "The Bruiser" - I used 18-14 Gauge-Cal Quick Splices (Vampire Splice). I wanted to splice Red and Black line from lamp to the Parking Lights. You can also choose other hookups such as Fog Lamps. This is for Parking Lights. The Parking lights are the ones that have a brown plastic adapter on the end. The adapt to the lower part of the lamp. On the Passenger and Driver side the Lamp Red Line should splice into the center line on the brown adapter. The Center line is purple/white. On the Passenger and Driver side the Lamp Black line should splice in the adapter line that is closest to the brown adapter release latch. On the Passenger side, the Lamp Black line splices to the Green/Black line of the Brown adapter. On the Driver side, the Lamp Black line splices to the Black line on the Brown adapter. If you choose to splice the line to the other outside brown adapter line, you will get a "disco" feature when you use your blinker. The Yellow Blinker light will alternate with the Halo doughnut LED lights. I tried this and undid it as I felt this would likely burn out the LED faster. Wire cutters are useful and I recommend not doing what I did. Spice at a distance far enough away from the Brown Plastic adapter so that if you make a mistake, you have room to correct. 2.5 hours with trial and error. I you can interpret my instructions, maybe an hour. Black out lamps look great and I am highly pleased on day 1.

Look good and are working well so far. It would be nice to have install instruction specifically for the make and model give the year but overall ok.