Speaker Wall Ceiling Mount Bracket One Pair for Universal Satellite, fits Keyhole and Thread Hole with 1/4 20 Threads, 4mm and 5mm Black 1ST

These are very well designed and made speaker mounts. I used them to mount my Sony SA RS 3 under my upper kitchen cabinets to compliment my soundbar and subwoofer. Clean concealed design, easy to install and adjust.

I'm specifically here to let those who own the Boston Acoustics Micro 110x surround speakers that these work! After 4 years being divorced I finally got my system back including a solid Denon receiver. However the ex lost the surround mounts, the power cord for the subwoofer, the remote you name it! Because my speakers have the mounts on the bottom this mount worked perfectly! Screwed right into the mount terminal, tightens up and very versatile. Got the wires run through the attic and ready to go. Waiting on the power cord for the sub but when it comes I am going to have a good old time! The speakers are 3 lbs and these mounts hold strong! One thing other reviewers have stated is that the ball at the end of the arm does get scratched so wait until you mount it to get it properly positioned but I am sure it will hold up to 5 lbs at least if not the specified 10. The hardware stinks as other stated so I grabbed a good set of drywall anchors at the local box store. I have no doubt these mounts will hold for the future. If you have the same speakers this is the mount! Great price, fast shipping and a perfect fit!

I used these to mount a pair of Polk Signature Elite ES10 speakers as surround speakers. They are rated for up to 10 lbs, and the speakers each weigh 6 lbs. If you are pushing the 10# limit and using the extended length bracket like I did, you might want to think twice. For my installation, I used these mounts on the wall beside the speakers and used the longer of the two included brackets. There was some sag on the speaker after tightening the bracket, so I had to aim the speaker higher than intended, tighten, and then allow the speaker to "sag" down to the desired angle. Not ideal, but after some trial and error, it worked. If someone were to bump the speaker, I am certain the mount would move/bend/break. I did install the mounts through the wall into wood studs, and the mount to wall is very secure. I had looked for a mount that was more secure, but this seemed to be the best I could find that used the threaded mounting option. I deducted one star due to it "sagging" after tightening, but would purchase again for my use, especially given the reasonable price and lack of substitute.

Perfect! Mounted on the ceiling, in corners. Pretty easy installation, and they solidly hold our Polk ES15 surround sound speakers (identical size [and weight, I think] to ES10's in case that helps anyone) pointing exactly the direction we wanted, which is diagonally down toward the center of the room. These were a great value for the price, and adjusting to get the angles "just right" wasn't too tough. Very happy with our purchase and would buy again.

There used to be a few generic speaker mounts specifically designed for junction box mounting, but they have all been discontinued for a long time and I was unable to find something similar anywhere. Another reviewer of this product modified it and mounted it directly to his junction box and posted photos of his setup. I won't reproduce his steps here, other than to say that instead of using a plastic blank wall plate, I used a metal one, and instead of driving one of the mounting screws into a block of wood, I just used a machine screw and nut combination for the mounting hole that was not being driven into the slots on the junction box (if you do this, make sure your speaker wire jacket is undamaged/properly insulated to prevent a short if they hit the machine screw. That being said, the method described by the other review would have also worked well, I just didn't have any extra lumber handy. Please note that my satellites are only 3 pounds--although this mount technically has a 10 pound weight limit, I would be very hesitant to mount any speakers heavier than 5 pounds using my method if you have plastic junction boxes (if your boxes are metal and properly secured to a stud, you might be able to use the full 10 pound limit). Overall, I'm very pleased with this hacky setup. Even when used in ceiling-mounted junction boxes, the mounts and speakers are sturdy and aren't going anywhere, and they allowed me to mount the speakers in an unobtrusive way that uses the existing junction box to hide the speaker wire.

These VideoSecu mounts were the perfect solution for mounting my MartinLogan Motion 4 bookshelf speakers. My speakers weigh 6lbs each, and these mounts hold them in place with no sagging. You do want to think ahead about how you will tighten the allen bolt once you have the speaker adjusted in the position you want it. A second person to help you will make it easier. It can be very tight getting your hand in the space between the wall and the speaker to tighten the bolt using the supplied allen wrench. A longer allen wrench from the hardware store would make this job easier. My speakers are mounted using standard 25lbs max drywall anchors and black #8 screws. They are not supplied, so you will have to buy these yourself. This combination holds up the 6lb speakers very securely. The default thread size for these mounts is 1/4" 20, exactly what my MartinLogan speakers needed, so I did not need to use the supplied 4mm or 5mm adapters, but it is nice to know that I have them in case I use these mounts with different speakers in the future. I am happy that all the hardware is black or painted black because it blends in very nicely behind the speakers. Other mounts have stainless steel (silver) screws and bolts, which draws attention to the mounting hardware. The all-black hardware that comes with these mounts provide a very clean looking installation. Will be purchasing another pair soon for my MartinLogan Motion 8 center channel, and will also consider these for my rear surround channels later when I add them to my system.

I tend to rely on reviews for a lot of products, so thought I would share my experience...especially for those who are considering electrical box mounting options. My new house came pre-wired for surround with electrical boxes. I was looking at the articulating kits that are designed for electrical boxes, but at $35-$40 each, I didn't want to spend ~$150 just to buy four of them. Completely ridiculous! Instead, I went to a local hardware store, bought four black electrical box covers for ~$1 each, and two pairs of these VideoSecu mounts (less than $40 total for all parts). I lined up the top hole of this mount with the top hole of the electrical box cover, and drilled a hole in the box cover where the bottom hole of this mount was. Then I drilled another hole in the box cover about ~1 inch below that for the speaker wire. I then took a small block of wood (approx 2" x 2" x 2") and drove one of the included screws through the bottom hole of this mount, through the pre-drilled hole (that I made) in the box cover, and into the block of wood. I then simply mounted the whole thing to the electrical box using the screws that came with the electrical box cover (ie, putting the top screw through the top hole of this mount, through the box cover, and into the electrical box). It took me a bit longer than if I had bought one of those electrical box kits, and might not work for heavier speakers (mine are ~3 lbs each), but it saved me over $100, and looks great! (I uploaded a picture to the customer gallery. It's rotated 90 degrees, but you get the point). Use that organ between your ears and save a little dough!

Excellent compatibility; the thumb screw adapts to the size you need. Minus two stars since the screws they supplied were too big for the drywall anchors that they supplied. I tore apart a piece of my ceiling trying to screw the supplied screw into the supplied anchor before realizing that I needed smaller screws. Insignia™ - 2.0 Mini Soundbar

Really good build quality. I've just ordered even more to keep on hand because I was so impressed by how small but sturdy these mounts are. I really like the angled attachment they come with too.

Se adaptaron a las bocinas Onkyo del teatro en casa que tengo y se ven muy bien.

👌

used to mount a pair of polk om3 speakers to the ceiling

Um ótimo produto