Thermal Grizzly TG Putty Basic 30 g Thermal Putty VRAM VRM PCB

I recently replaced the thermal pads on my GPU with Thermal Grizzly TG Putty (Basic), and I couldn’t be happier. It supports heights between 0.2 mm to 3 mm, so no more guesswork—just scoop, apply, and smooth. It comes with handy spatulas and plenty of material in the tub. 🔧 What I Love: Non-conductive & versatile — safe to apply on VRAM and VRM chips without worrying about shorts. Fills irregular gaps seamlessly, unlike thermal pads that can tear, compress unevenly, or age poorly. Noticeable thermal improvement — VRAM temperatures dropped significantly after switching to putty. ⚠️ A Few Caveats: Application takes patience — getting a clean, even layer isn’t hard, but does take care. Heatsink pressure matters — make sure there’s enough mounting pressure, or temps can rise instead of drop. 💰 Worth the Price? Yes. The Basic version is a solid value for most use cases. There are higher-end versions (Advance and Pro) with slightly better thermal performance, but for the price, Basic delivers excellent results. 📌 Final Verdict: If you’re confident working inside your GPU or laptop and want an upgrade over thermal pads, TG Putty is a fantastic choice. Just take your time applying and make sure the heatsink is properly secured.

Great value for price. Easy application and it works as intended. I replaced the putty of my laptop with this new one and together with replacing the thermal paste with PTM 7950, it helped cool down the temperature. It comes with a small spatula and this also helps. Overall, I recommend the brand and the product.

Worked great on my waterblock for the 7900XT and reduced the VRAM temperatures from the stock pads. It makes measuring a lot easier, as it will just squash into place. The only problem is the price is a bit high.

Used on my Inno3D iChill x4 RTX 3090 to rescue it. The card's VRAM was overheating causing bluescreen crashes. I took it apart, and found the rear plate pads were OK, but the front pads were dry and crumbling, so I liberally replaced all the front thermal pads with this TG Basic Putty, and repasted the GPU die with new thermal paste. There was not enough in the tub to replace the rear pads, but they were in good condition, so I spread the remainder as a thin layer to interface between the rear contact surfaces with the existing thermal pads on rear heat plate, to seal any micro cracks in those existing pads. The result has been that the card is now working perfectly again, and temperatures have dropped about 20 degrees C on the VRAM, and no more bluescreens or crashes.

Good product easy to spread and compresses well with cooler on top, temps are down for me definitely worth buying if replacing the thermal liquid on processor fills gaps easy

Excellent Putty, used for an Xbox Series S improved performance and cooling form stock, paired with a fresh coat of Thermal Paste (MX6 Artic). Good value. I liked that it came with spatulas and gloves, it was a bit messy trying to not get it on everything was a challenge, easy enough to apply on where I needed it to go. Would defiantly buy again. improved the performance and temperatures of the Series S. Improved fan noise level due to better cooling from paste and putty. Fresh smells too which is always good for electronics.

Worked well, repasted and reputty on an Xbox Series X for my housemate, dead silent afterwards. It is quite sticky and feels very wet, you wont be able to roll nice little snakes out of it, but it works albeit a bit messy

Thick and not to sticky drop temps better then pads.

4~5年くらい使ったRTX3070tiのGPUのカピカピグリスの塗り替えのついでに。 サーマルパットではあまり流通していないマイナーな厚さがあったため、ならばサーマルパテにしようと思い購入。 cpuにグリスを塗る感覚でメモリに塗ると全く足りないので、一度塗ってからヒートシンクをつけて外して両面に十分接着しているか確認するのをお勧めします。また、GPUホットスポット温度も合わせて確認すると安心だと思います。 サーマルパッドの時よりも多分冷えてると思うので、こっち使ったほうがいいですよ。とてもおすすめです。 内容量30gとありますが、私の場合は十分余ったので足りないことはないと思います。

This stuff works great! I only use thermal grizzly products now for paste and putty. Save the money and get this stuff over the two other premium tiers as this literally works fine as is! I used it on my RTX 3060 laptop as the old pads were literally dry and crispy lol! Dropped my VRM temps back to normal and was super easy to apply. It dissolves with ISO same as their thermal paste for easy cleanup:) Cheers

Usato su una XFX QUICK 308 Rx 6650 XT 8GB, ottimo prodotto, richiede un po' di manualità, ma meglio dei classici Thermal Pad dove bisogna conoscere lo spessore da usare, all'interno si trovano: -certificato thermal grizzly -manuale -2 guanti neri -3 spatoline -1 barattolino Thermal Grizzly 30g

I have done many projects with this one it comes Handy but it’s impossible to clean it in room temps avoid cleaning it in hot weathers and after use

Très bonne pate pour remplacer des pads thermiques de différentes épaisseurs sur les cartes graphiques dans mon cas , redonner une jeunesse a une 970 gtx g1 ,par contre prendre son temps pour l'application la pâte est très très souple, un conseil pour bien la manipuler la mettre quelques minutes au frigo et la manipulation devient plus facile