LOTOS LTPDC2000D 2024 Upgraded 3 in 1 Plasma Cutter TIG Sitck Welder Combo, 5/8" 16mm Clean Cut 3/4" 20mm Severance Cut 50A Non-Touch Pilot Arc Plasma Cutting Machine, 200A Tig & Stick Welder, Brown

I have worked in the industrial maintenance field for 30 years and have a shop at home. I was really wanting a plasma cutter for home and was searching the internet and found this machine. The reviews were mixed but for the price I thought I would give it a chance. All I can say is WOW. It has paid for itself over the years! I have used it now for 3 years and have no complaints. As a plasma cutter it is as nice as the hypertherm I have at work. I have had no problems cutting up to 3/8" steel with it. The leads are a good length and can handle a lot of cutting The arc feature works good too. The duty cycle is a little low for big, high power jobs but it works great! The tig feature works great for small jobs. There is some limitations to this machine... it only really works good when running 220v, it works ok at 110v but really doesn't have the punch to do much work. The arc leads are small, short and not made for a lot of work. Overall it has been one of the best investments in tools i have ever made. If it died tomorrow I wouldn't be upset. Update- 5 years now and it still works great! It has hundreds of hours on it and still good a new! Great machine for home shop or farm! I have ran this with my portable generator for field repairs and it works great!!!

Never plasma cut before but I did a considerable amount of stick welding over the years (Lincoln Electric) . My Lotos LTPDC2000D arrived today. I immediately popped the case open to verify all connections, etc were intact (plus, I really wanted to see what I bought). Found the power output connector bolts and the pilot arc connector nut to be loose. I tightened those up and also went over all the screws securing the MosFETs to the heatsink (I'm an electronics guy)..... see pics, especially check the points indicated with blue arrows. I note lots of sensor feedback points in the circuitry for current, temperature, voltage, etc (which is impressive). The electronics is very well laid out and the configuration maximizes airflow over all components especially through the two massive MosFET heatsinks. Also made certain the fan was free to rotate. With that done, I closed it up and gave it a try. This thing works exceptionally well, much better than my expectations. I've been plasma cutting and stick welding all day with it, building a welding cart. The pilot arc starts immediately when triggered and the compressed air continues to flow for a few seconds after trigger release, to ensure proper torch cooling (two user settings for this 2.5 & 6 secs). Only peave is, it starts up in the default plasma mode, does not remember last used mode setting, but this is certainly nit-picking on my part and not a real concern. Excellent machine, very good price point, well engineered construction and good attention to details. Very glad I finally bought it!

I'm a diy hobbyist. I've been welding for 7 years, but wouldn't consider myself a pro. Here's my impression. I chose this unit because it was only another 200 for the 3in1 ability. Review based on using 220v. Have not (and don't plan to) used 110v. Plasma Has pilot arc! Means all you need todo is pull trigger and it arcs as aposed to scratch start. Cuts 1/4 inch steel very well. Might do 3/8, but wouldn't buy it if that's what you cut the most. I run it off a a 21 gallon harbor frieght compressor. The cfm the unit needs isn't too high. Not a fan of the supply line for air, but the I haven't changed it so it works fine. Nice air regulator. Stick/ Arc Leads are short. Real short. Otherwise works well. Goes up to 199 amps, I use it anytime I need to weld dirty metal together. Usually running 1/8" 6010 Lincoln rods. TIG D.C. ONLY. DOES NOT WELD ALUMINUM. I've used this quite a few times. Comes with regulator, but the unit uses the same supply line input for both tig gas and air for plasma. If using both often, I recommend a 3 way ball valve. It sucks having to change the hose each time, but again I haven't changed it lol. I bought the pedal, it's worth it. Again pilot arc, no destroying tungstens trying to strike an arc. I've penetrated 1/4" before testing it, but mostly use the tig function for thin sheet metal and small parts. uses a wp17 torch. Lots of machines use this torch, tons of consumables available. Overall it's a pretty good machine for the money. I use it often building off road trucks mostly plasma and tig, but it's nice having the stick welding option. Giving it a 4 out of 5 because it does have a few little things that bug me, but they have nothing todo with the functionality of the machine

Bought it when a sale was on. wired it for 230VAC only and have used the plasma cutter a fair amount- including cutting a complete 1970's car into pieces to be taken to the metal recycler. Stick welded for the first time in 20 years and the welds came out fine. Seems to have plenty of amperage available. Also tried tig welding for the first time- I will need some practice but it's not the welders fault. Would like to state that there are no free consumables or anything else offered , regardless of the review- this must have been a practice that was dropped (imo that's a good thing)... Concerns: The 3 year warranty that was being offered has been cut to 1 year and return shipping costs are $$ also the repair cost after the warranty expires appears to be $ 319.00 ( over 3/4s of the NEW purchase price) and not sure if that includes shipping?? Also if there is a problem down the line it would be nice to be able to source schematics ( not included in manual), circuit boards and individual parts. (some manufacturers offer this). for myself and other electronics technician DIY. Update: been using it for over a year now with no complaints, Has never shut down from running up against it's duty cycle on any of the processes. Once again- very pleased with this combo unit- The $399.99 price for such a capable multi function cutter / welder is the best deal i have seen. but would feel better if the warranty were longer and parts could be sourced without sending the unit in if a problem develops after it is out of warranty. added pictures of a hydraulic press that the plasma did all the cutting for and a set of pallet forks converted for my tractor. which also used plasma and stick functions for. Update 2 almost 4 years of Use. Have had to clean the plasma cutters torch switch, would not trigger consistently until the contacts were cleaned. Working great now in all functions. It has more than paid for itself. Update 3 4 1/2 years of use. Plasma torch button failed. As posted before I cleaned it but it finally died. Bought a $6 replacement switch from plasma dyne with a better quality switch. zip ties and some electrical tape after soldering in the 2 wires. Plasma cutter works great again Also still stick welds and TIG welds Excellent interim update: Lotos has updated the circuit boards - should simplify wiring and maybe even improve reliability see my pics versus reviewer who bought more recently and posted the circuit board pictures Going on 7 years of use now. Really can not complain. Still Going Strong Had a rush job to cut up a 55 foot mobile home frame. Did it all straight through, the only breaks were for me.... Every weld that this unit made has held up. No failures Several more projects including severing 5/8 steel for a Backhoe hydraulic thumb and modifying a Harbor freight backhoe bucket to fit the older TLB. In September the 3 in 1 Lotos will have provided ten years of service. It paid for itself in successful jobs years ago.

The plasma cutter with the pilot arc cuts beautifully through even heavily rusted steel. Igniting the torch produces about an inch of plasma, and it gets right to work. It has no trouble cutting through heavily rusted steel plate. Aluminum is a breeze. The newer version of the welder has separate gas intakes for argon and for compressed air. The compressed air has an easy to adjust regulator on the front panel. The bad news/good news: The first welder that Lotos sent didn't have a working pilot arc. After some quick troubleshooting, the customer service team was very helpful and gave me a replacement torch, which didn't fix the issue, and then sent a complete replacement welder, which worked wonderfully. Much as I dislike not getting a working item first time, I love it when customer service rises to the occasion, and is helpful and effective at solving the problem. The team at Lotos did an A+ job. It has given me great confidence in the team at Lotos. While it was being diagnosed, I had a chance to see inside the welder, and the build quality on this welder (2019 brown LTPDC2000D) is excellent. The boards are well laid out, with several large heat sinks and lots of heavy copper where needed. The newer versions of this welder come with an L6-30 twist lock plug attached. This welder takes a slightly different set of consumables for the plasma cutter. Make sure that you get the ones for the brown plasma cutter. I bought the optional foot pedal, and I really love it for regulating TIG welding; it is much easier to get exactly the weld I want.

Arrived quickly the cord is very short but I needed a adapter plug for my shop anyway. Trip to meander to get a plug to match my wall recpticals. A recpticals to match the welder and 25' 10 ga cord to carry the load and I was in bisuness. Wish I would have ordered the 120 adapter at the same time. Tryed the plasma cutter first it cut the sheet metal scraps I had laying around nicely. Used the stick welder next it starts nicely and did a better weld than I have been doing. I don't stick weld much. Had to wait a few days to try the Tig fortunately it uses the same consumables as my welding truck. They should have a least put one in with it. But I need to bring a gas bottle home anyway. I was very pleased with the stainless weld I did on a couple chair legs. The only minor gripes I have are the welding leads are to short. But both the plasma and Tig torches are good quality. And consumables aren't very expensive. I ordered them after the fact the stick weld stinger and ground clamp are good quality just a little short.

I got a lot of use out of this product for a couple years and then ran into a problem with the circuit board. I emailed the manufacturer and after sending a few pictures they sent me a brand new machine. That was 3 years ago and the Machine is still running perfectly. I use this machine to build my own portable, trailered CrossFit rig so I could work out anywhere. I cu a lot of metal and stuck a lot of metal together with this machine. For all the processes you get, it is well worth the money.

LTPDC2000D, I bought it on an lightning deal for $350 so far its been ok, it seems to need more argon than it should welding 3/16th steel, but it has plenty of power to weld 5/16. I have yet to try it on anything thicker. The first thing I did was add a shelf to my welding cart I already had that was made from 1.5" 3/16" wall square tubing. it has good power for what it is (a cheap welder from Amazon) I am just doubtful of the longterm reliability. So far it has cut ⅜ with ease but I have a High CFM compressor and a ⅜ line connected to it running at 80psi with a good quality air dryer. When I tried it with my portable it was a little anemic and didn't want to cut very thick steel. The 30amp plug is stupid on a 40/45amp machine, but I rolled with it and added a 30amp outlet to the end of some 8/4 I had with a 50amp RV plug on it. I can move around my shop fairly freely with the 8/4. The cutter guide is CRAP and its a size that you can't get a cheap rolling guide for it. I wish you could drag cut with it. So far it has yet to not start an arc, except for the few times I forgot to reattach the ground clamp and every time my first thought was "I wasted $350" The regulator that comes with it is cheap and unless you keep the flow up on the argon or re-route the 3-way valve to only use it for air you waste argon. I haven't used it for stick yet.

Despues de la compra estaba un poco preocupado por mi opcion de adquirir esta soldadora/cortadora plasma. Asi que me dedique a investigar acerca de la marca y quede muy impresionado con los servicios que tienen. En cuanto llego puse manos a la obra y ensamble las partes necesarias para soldar con arco, cortar con plasma y el tig. Una excelente opcion para aquellos que no somos soldadores profesionales pero que necesitamos una planta pequeña eficiente y confiable que haga el trabajo necesario. Ampliamente recomendable.